Dryer Drum Not Turning

What it looks like

Your dryer runs but the drum does not rotate. You may hear the motor humming or the dryer may make a low‑frequency whirring sound, but the drum stays still.

What the Problem Looks Like:

  • Dryer starts, lights turn on, and the timer counts down, but the drum remains stationary.
  • You may hear a faint humming or buzzing from the motor.
  • No tumbling action, so clothes remain wet after the cycle.
  • Occasionally a clicking or clunking noise precedes the failure.
  • Drum does not spin or tumble.
  • Dryer makes a humming noise but no movement.
  • Clothes are hot but remain damp.
  • Cycle completes but clothes are not dry.
  • Unusual noises (squealing, grinding) before the drum stops.

Why it happens

  1. Broken or slipped dryer belt – The belt that turns the drum can snap or slip off the motor pulley.
  2. Failed dryer motor – The motor may be burned out, have a seized bearing, or its winding is damaged.
  3. Faulty drum rollers or idler pulley – Worn rollers or a broken idler pulley can prevent the drum from turning.
  4. Clogged or broken drum support rollers – If rollers seize, the drum cannot rotate.
  • Broken drum shaft or broken drum support rollers.
  • Faulty motor capacitor (for models with a start capacitor).
  • Obstructed drum belt tensioner or broken tensioner spring.
  • Electrical issues such as a blown thermal fuse that stops the motor while the control board still thinks the dryer is running.

When the belt snaps or slips, the motor still receives power and may hum, but there is no mechanical link to the drum. A motor failure stops torque transmission, leaving the drum idle. Worn rollers or a broken idler pulley increase friction, causing the motor to stall. Electrical components like a failed capacitor prevent the motor from starting under load, resulting in a humming sound with no drum movement.

How a technician diagnoses it

What You Can Safely Check:

  • Unplug the dryer and inspect the dryer belt for cracks, breaks, or looseness.
  • Visually examine the drum for any obvious obstructions or broken parts.
  • Spin the drum by hand (with the dryer unplugged) to feel resistance.
  • Listen for a humming sound when the dryer is turned on; if you hear it, the motor is likely receiving power.

What a Technician Will Inspect:

  • Remove the dryer’s front or rear panel to access the belt, motor, idler pulley, and drum rollers.
  • Test motor continuity with a multimeter and check for proper voltage at the motor terminals.
  • Inspect the motor capacitor (if applicable) for bulging or leakage.
  • Examine drum rollers, drum shaft, and idler pulley for wear, breakage, or seized bearings.
  • Verify the thermal fuse and high‑limit thermostat are intact.
  1. Power Check – Verify the dryer receives proper voltage (120 V for electric models, 240 V for gas dryers).
  2. Belt Inspection – Remove the dryer’s front panel, locate the belt, and look for breaks or slippage.
  3. Motor Test – Using a multimeter, check motor resistance and continuity; test for proper start-up voltage.
  4. Roller & Pulley Evaluation – Rotate the drum manually; feel for gritty or stiff spots indicating worn rollers or a seized idler pulley.
  5. Capacitor & Fuse Verification – Test the start capacitor and thermal fuse for continuity.
  6. Final Run Test – Reassemble and run the dryer to confirm the drum turns.

Repair options and what they cost

Possible Repair Solutions:

  • Dryer belt replacement – Replace a broken or stretched belt. This is often the most common and cost‑effective fix.
  • Motor replacement – Install a new dryer motor if the existing one is burned out or has a failed start capacitor.
  • Idler pulley or tensioner replacement – Replace a broken or worn pulley/tensioner to restore proper belt tension.
  • Drum roller or drum shaft repair – Replace worn rollers, drum shaft bearings, or the drum support assembly.
  • Capacitor replacement – For models with a start capacitor, replace a faulty capacitor.
  • Thermal fuse or thermostat replacement – If these safety components have failed, replace them to allow the motor to run.

Parts/Components Involved:

  • Dryer belt (specific to model)
  • Motor assembly
  • Idler pulley or belt tensioner
  • Drum rollers and drum shaft bearings
  • Start capacitor (if applicable)
  • Thermal fuse and high‑limit thermostat

Repair vs. Replacement Considerations:

  • Age of dryer – If the dryer is over 10‑12 years old, multiple component failures may make replacement more economical.
  • Cost of parts – Motors and drum assemblies are pricier than belts; evaluate total repair cost versus a new unit.
  • Frequency of failures – Repeated belt or roller failures may indicate underlying motor issues; a motor replacement may be wiser.

Typical Factors Affecting Repair Cost:

  • Model and brand (premium brands may have higher‑priced parts).
  • Availability of OEM vs. aftermarket parts.
  • Labor time – Belt replacement is quick (≈1 hour), motor or drum assembly replacement can take 2‑3 hours.
  • Need for additional parts (e.g., new rollers when replacing the motor).
  • Service call fees and any required disposal of old components.

Safety first

  • Always disconnect power before inspecting or working on the dryer. Unplug the unit or turn off the circuit breaker.
  • Do not attempt to replace the motor or drum assembly unless you have proper tools and experience; these components are heavy and can cause injury.
  • Watch for sharp edges on the belt and metal components; wear gloves to protect your hands.
  • Avoid inhaling lint or debris when opening the dryer; wear a dust mask if the interior is heavily soiled.

When to Stop Using the Appliance:

  • If you hear a humming sound but the drum does not turn, stop the dryer immediately to prevent motor overheating.
  • If the dryer emits a burning smell, unusual grinding, or squealing noises, cease operation and call a professional.
  • Do not run the dryer with a broken belt, as the motor can overheat and cause a fire hazard.
  • If the dryer fails to tumble after multiple attempts, discontinue use until inspected by a qualified technician.

Frequently asked questions

Why does my dryer motor hum but the drum won’t turn?

The motor is receiving power but cannot transmit torque to the drum, often due to a broken belt, a seized motor, or a faulty idler pulley.

Can I replace the dryer belt myself?

Yes, if you are comfortable disconnecting power and removing the dryer’s front panel. Follow the manufacturer’s service manual for belt routing.

How long does a dryer belt replacement take?

Typically 1–1.5 hours for most residential models.

What causes the dryer belt to break?

Over‑tightening, age‑related wear, excessive lint buildup, or a misaligned idler pulley can cause premature belt failure.

My dryer makes a humming noise and then shuts off. Is this a motor issue?

It could be a motor that is overheating or a failed start capacitor. A technician will test the motor windings and capacitor.

Is it safe to run the dryer without a belt?

No. Running a dryer without a belt can damage the motor and cause overheating, creating a fire risk.

How much does a dryer motor replacement cost in Stone Mountain?

Costs vary by brand and model, but typical labor plus parts range from $250‑$450. A precise quote requires a diagnostic visit.

Will a new belt fix a drum that still won’t turn?

If the belt is the only issue, yes. However, if the motor, rollers, or idler pulley are also damaged, additional repairs will be needed.

Related guides

Book a repair in Stone Mountain

Call (470) 847-9076 with your brand, model number and any error code showing, or book a repair online. The model number lets us check parts availability before the visit. We cover Stone Mountain, Smoke Rise, Tucker, Clarkston, Lithonia and Redan.

See the dryer repair cost guide, how the diagnostic fee works, or browse all problem guides. Tap here to call.